MB Trac 1400 – real transmission ratios V 1.0 CnC



The following things have been adjusted:
– Real translations of the second group of the gearbox (several groups do not support CnC at the moment, so the field group is not available). There are a total of three transmission variants that occur in reality like this.

Variant 1: Final speed 40 km/h – 8 gears – reverse gear corresponds to 3rd gear + 3% faster

This variant corresponds to the vehicle in play with the short final drive ratio (to be seen on the gear table on the dashboard). was delivered ex works.

Variant 2: Final speed 40 km/h – 7 gears – reverse gear corresponds to 3rd gear + 3% faster

This variant was also delivered from the factory with the long final drive ratio.

Variant 3: Final speed 50km/h – 8 gears – reverse gear corresponds to 3rd gear + 3% faster

The 8th century The 8th gear was often opened by the Trac drivers in the gearbox (illegally) in order to go faster or to save fuel at 40km/h, because the engine doesn’t rev up as much then.

– The shifting behavior in automatic mode was individually adapted for each gear.

I had to make compromises here because there are no load-dependent switching thresholds. So it can happen that the transmission sometimes shifts back and forth in the field because one gear is too low and the next too high. But this happens relatively seldom.

– The AI is now faster on some jobs (e.g. cultivating), because the changes shift to the next higher gear.

I can give the following hint: I have noticed that the AI with the Trac, the 3m Köckerling cultivator and weight block sets 10 km/h as working speed on the field. Without weight in the front hydraulics it is 15 km/h, which is set by the cruise control. This must be related to the total weight of the vehicle. The gear selection of the AI also depends on the preset speed. I could not find out why only the 3rd gear is used for cultivating and the 4th gear for 15 km/h. It works much better when ploughing. There the AI uses the gears sensibly. Therefore I recommend to let the AI work with cultivator without front weight, because the 15 km/h are not reached by the tractive power anyway. At the same time, the speed of rotation is reduced and thus fuel is saved.

– The efficiency through the gearbox has been changed to a realistic value. As a result, the Trac has lost about 25% of its power!

– The power development is not so spontaneous anymore. The throttle response is significantly reduced. In general, I have tried to find a compromise that works well in the field as well as on the road. All in all, the Trac must now work much more. Loaded trailers are harder to pull and inclines have a significant influence on the final speed. Ploughing works best with the 4-share Lemken. On level fields, the 5 coulter also works. If it becomes too steep, the speed with the 5 coulter can be reduced to 3 – 4 km/h.

– The tank volume was corrected to 240l.


Credits:
-
1 Star2 Stars3 Stars4 Stars5 Stars (No Ratings Yet)
Loading...


What is Cattle and Crops mods

There’re so many opportunities in this world. However, not many are able to see them so we’re ready to show you some. Everyone of you’ve heard off mods but it’s important to know what’re exact advantages after you install them. Cattle and Crops mods can provide everything you want. It doesn’t matter whether you’re looking for a new tractor, combine or maybe you want to change maps, texture or the game itself. Everything is being done just by installing CnC mods. You can find so many different mods with different possibilities inside them so take a closer look and take the ones you find necessary most. This can be nominated as the greatest opportunity of your lives because all the Cattle and Crops mods are absolutely free. Such a wide variety doesn’t cost a single cent and such huge possibilities are hidden in each mod. This is a chance you cannot miss.

You may also like...

Leave a Reply

Your email address will not be published.